Lotus Europa Community
Lotus Europa Forums => Garage => Topic started by: surypap3 on Friday,June 12, 2020, 03:08:31 PM
-
I did a couple quick searches looking for DIY instructions on replacing the output shaft seals on a 365 transmission. Does any one have a narrative on the process?
-
:Welcome: surypap3!
Sorry I can't help you with your seals. I think someone can probably either explain it or point to a post that explains it.
-
Is your transaxle quiet and whine free? No off-throttle noises either?
-
Quiet and performs well. However, I am now experiencing inability to shift into reverse. I thought maybe linkage adjustment, but I disconnected the linkage at the shaft and could not manually shift into reverse. Yesterday was the first day in 5 years the car has been on the road with no prior shifting issue.
-
Probably the rear linkage u-joint yoke to shaft play. Check for a loose pin and play on the shaft. The usual fix is to drill for a near press fit bolt and to slice the yoke in one spot so the bolt can clamp to the shaft, eliminating any play. These things don't like to shift into reverse, and if you looked at the mechanism inside the box, you would see why. I think I only get into reverse 50% of the time on the first try.....lol. Also check for interference with getting the required rotation and fore-aft movement needed for reverse.
Jerry Rude
4005R
-
If the transaxle is quiet, then you can can the seals in situ if you're careful. Lots and lots of people futz this job up. So BE CAREFUL. The seal nuts also locate the diff carrier and tension its bearings. There is NO margin for error. Close is not good enough.
DO ONE AT A TIME!
MARK THE SEAL NUT'S POSITION, count turns (whole and part), carefully note and mark where it becomes free so you start it in the same place, and can return the nut to EXACTLY the same place.
The seal goes in from the inside of the nut. Light, non-setting, sealer around the outside of the seal and on the seal nut threads. Light grease on the seal lip. Replace the inner o-ring as well. Light grease on the o-ring. After the seal nut is back in place, make sure the splined, inner seal land pops in place over the o-ring -- not an easy task so make sure it does. Some people use the half shaft and the weight of the car to do the job.
When you're done carefully shim the driveshaft yokes as well.
-
With regard to reverse selection also check the external reverse detent under as plastic cover on the rear of the gearbox. Does it select 5th ok? As the detent works for reverse and 5th.
Also on the seal replacement, the inner o-ring I dont think this is available any more.
-
You may need to turn a wheel to get the teeth in align for it to shift into reverse.
-
Remember that reverse on most(all?) manual transmissions has no synchronizer so that the engagement teeth can be aligned with each other and not go into gear, if you put it into first and barely move the car the alignment of those teeth will change and will allow you to engage reverse without grinding gears :)
-
Attached is a photo of my U-joint connection to the rear of the 365 transaxle. I drilled out the hole for a 5/16" bolt and used a hacksaw to cut a slot in the U-joint piece. By tightening down the bolt, the U-joint is clamped to the transaxle shift shaft thus taking up all play. I also rebuilt the U-joint replacing the cross shafts and the needle bearings.
Tom
74 TCS-4605R
-
:Welcome:
-
All good feedback … Thanks! WRT the reverse problem, the detent aligns and I do have 5th gear. I have tightened the shift linkage attachment to the trans shaft. There is no slipping with the connection. My connection to the trans shaft uses split pieces with the bolt going thru each and the shaft for tight clapping. Drove the car today hoping that since it sat for 5 years, it may help to get the gear lube hot and flowing. But still no luck. With regards to the seals, they are available and the instructions provided are clear but make me a bit nervous to undertake this task. I know I will also need a special tool to remove the nuts. I may have to contact jbcollier for coaching (if 0k).
-
It's not hard job. You just can't be casual about it. Pay attention, make notes and you'll be fine.
-
If the transaxle is quiet, then you can can the seals in situ if you're careful. Lots and lots of people futz this job up. So BE CAREFUL. The seal nuts also locate the diff carrier and tension its bearings. There is NO margin for error. Close is not good enough.
DO ONE AT A TIME!
MARK THE SEAL NUT'S POSITION, count turns (whole and part), carefully note and mark where it becomes free so you start it in the same place, and can return the nut to EXACTLY the same place.
The seal goes in from the inside of the nut. Light, non-setting, sealer around the outside of the seal and on the seal nut threads. Light grease on the seal lip. Replace the inner o-ring as well. Light grease on the o-ring. After the seal nut is back in place, make sure the splined, inner seal land pops in place over the o-ring -- not an easy task so make sure it does. Some people use the half shaft and the weight of the car to do the job.
When you're done carefully shim the driveshaft yokes as well.
When you say "make sure the splined, inner seal land pops in place over the o-ring", can you clarify that for me? Also, for a "light, non-setting sealer", what would you recommend? Thanks
-
Hylomar Blue:
https://www.amazon.com/Valco-Cincinnati-Hylomar-Gasket-Sealant/dp/B00CFH9GZG/ref=sr_1_1?dchild=1&keywords=hylomar+blue&qid=1592258828&sr=8-1
Permatex Aviation Form-a-Gasket #3
https://www.amazon.com/Permatex-80019-Aviation-Gasket-Sealant/dp/B000HBM3QQ/ref=sr_1_1?crid=PL39XN7DI6DB&dchild=1&keywords=permatex+aviation+form-a-gasket+no.+3&qid=1592258922&sprefix=permeates+aviation%2Caps%2C242&sr=8-1
and others.
The o-ring and the seal land/run/ring can be found here:
http://www.lotus-europa.com/manuals/s1parts/f/f6.htm
o-ring - 46F6140
seal run - 46F6141
The seal run has a groove in its bore for the o-ring. Takes a fair amount of pressure to get it to "pop" over the o-ring.
-
Thank you. I saved this info to a file for when I venture into this. Still struggling with the no reverse. So holding off till I see if the case needs to be opened to figure out the reverse issue. Any thoughts on that?
-
Can you explain exactly what it doesn't do? Won't move into the reverse gate beyond the 1-2 gate? Won't move into reverse once it's in the reverse gate?
-
It can also be difficult to get the ring out. Does anyone have any tips?
-
You can't remove the ring without either removing the seal nut, or damaging the seal.
-
You can't remove the ring without either removing the seal nut, or damaging the seal.
I mean with the seal nut off, getting the ring out seems to require a lot of effort. What do you use?
-
Picks with a 90 degree end like this:
https://m.aircraftspruce.ca/catalog/topages/pickhook.php?gclid=EAIaIQobChMI5-S19rSJ6gIVlR6tBh0YiQ6JEAQYCCABEgJcnvD_BwE
-
Can you explain exactly what it doesn't do? Won't move into the reverse gate beyond the 1-2 gate? Won't move into reverse once it's in the reverse gate?
In attempting to go into reverse, I can move the shifter laterally into the position where it pushes up on the detent ball, but then moving the shifter back into reverse goes nowhere. It feels completely blocked. The detent ball does not fully go into its housing if that makes any difference. But nor does it when going to fifth. 5th operates just fine.
-
Reverse is selected by moving the shifter backwards which then moves the selector forward.
Disconnect the linkage at the transaxle and turn the selector manually into the reverse gate and then push the selector forward.
-
Hi surypap3,
:Welcome:
Mark
-
Reverse is selected by moving the shifter backwards which then moves the selector forward.
Disconnect the linkage at the transaxle and turn the selector manually into the reverse gate and then push the selector forward.
I have tried that (eliminate the shifter and linkage) with the same results experienced using the shifter. The shaft will not go forward into reverse. Ugh! It is solidly blocked from going forward.
-
Lastly, remove the external detent and try again -- I don't think it will help but it's worth trying.
Again, you have rotated there wheels while trying to engage reverse?
If yes, you will have to remove the rear cover and see what's up.
-
Thanks for the ideas. Clarification on removing the external detent …. there is a ball/housing and a cam, which are you referring to for removal? BTW, the Ball never goes completely into the housing when pushed by the cam? Is that wrong?
The process of turning the wheel ….. do this while trying to manually shift into reverse? Or move the wheel slightly while in another gear, then try reverse?
Thank you!
-
Move the wheel while in neutral, you are trying to turn the gears on the output side so the tips of the teeth don't line up with the input side. I think you might possibly need one of the rear wheels on the ground, or stopped from rotating, so the diff engages with the gearbox on the easiest side to turn (ie the one off the ground you are turning!)
-
OK. That should be easy to try! Thx
-
If you remove the housing with the ball and spring for the reverse and fifth gear detent ( I've never done this, but mark it's position frirst) it should make it easier to get it in to gear, as this is what gives most of the extra resistance to selecting these gears
-
Move the wheel while in neutral, you are trying to turn the gears on the output side so the tips of the teeth don't line up with the input side. I think you might possibly need one of the rear wheels on the ground, or stopped from rotating, so the diff engages with the gearbox on the easiest side to turn (ie the one off the ground you are turning!)
I gave the wheel turning a whirl (so to speak), just did not happen. I think I am close to looking for someone who could open the case and knows his way around at this point. Any ideas?
-
Someone check me on this but I recall removing the rear cover should be done with a particular gear engaged.
I'm sure it's in the manual.